LED Cube RGB 4x4x4: Difference between revisions
Created page with "==Intro== This LED Cube RGB 4x4x4 is actually based on Charliecube designed by Asher Glick, which all the informations are available at https://aglick.com/charliecube.html..." |
No edit summary |
||
| Line 6: | Line 6: | ||
And these are the 2 boards. | And these are the 2 boards. | ||
[[ | [[File:Boards.JPG|600px]] | ||
<br>The left one is for LED Pillars. And the right one is for the controller board. | <br>The left one is for LED Pillars. And the right one is for the controller board. | ||
<br><br> | <br><br> | ||
| Line 12: | Line 12: | ||
And here are the circuit boards with all the LED Pillars soldered, and the controller board assembled with all the components. | And here are the circuit boards with all the LED Pillars soldered, and the controller board assembled with all the components. | ||
[[ | [[File:2modules apart.jpg|600px]] | ||
<br><br> | <br><br> | ||
And here is the picture of the LED Cube RGB 4x4x4 in complete form. | And here is the picture of the LED Cube RGB 4x4x4 in complete form. | ||
[[ | [[File:Assembled.jpg|600px]] | ||
<br><br> | <br><br> | ||
| Line 23: | Line 23: | ||
LED board<br> | LED board<br> | ||
[[ | [[File:CubeRGB444 LEDs.png|800px]]<br><br> | ||
Controller board<br> | Controller board<br> | ||
[[ | [[File:CubeRGB444 Minsys.png|800px]]<br><br> | ||
==Komponen== | ==Komponen== | ||
[[ | [[File:Components.JPG|800px]] | ||
Here are the list of all the components needed for these boards. | Here are the list of all the components needed for these boards. | ||
| Line 66: | Line 66: | ||
==Tersedia di== | ==Tersedia di== | ||
The circuit boards with all the components needed are available in a form of a Kit, complete with the jigs needed. | The circuit boards with all the components needed are available in a form of a Kit, complete with the jigs needed. | ||
[[ | [[File:Kit single.JPG|800px]]<br><br> | ||
Available at marketplaces below : | Available at marketplaces below : | ||
* https://bit.ly/TP-PALTA (Tokopedia) | * https://bit.ly/TP-PALTA (Tokopedia) | ||
Revision as of 08:26, 7 June 2020
Intro
This LED Cube RGB 4x4x4 is actually based on Charliecube designed by Asher Glick, which all the informations are available at https://aglick.com/charliecube.html
What I made here is a PCB version, which all the circuitry were made into 2 separated boards, which then will be connected using headers. And these are the 2 boards.
The left one is for LED Pillars. And the right one is for the controller board.
And here are the circuit boards with all the LED Pillars soldered, and the controller board assembled with all the components.
And here is the picture of the LED Cube RGB 4x4x4 in complete form.
As references, here are the schematic of the 2 boards above.
LED board
Controller board
Komponen
Here are the list of all the components needed for these boards.
- RGB LED 5mm Common Cathode : 64pcs
- Wire : 64pcs
- IC ATMega328P-PU : 1pcs
- IC Socket 28pin : 1pcs
- Crystal 16Mhz : 1pcs
- Capacitor 22pF : 2pcs
- Capacitor 0.1uF : 6pcs
- Capacitor El 10uF : 2pcs
- Resistor 10k : 1pcs
- Resistor 1K : 1pcs
- Pin Header Female 1x6 Right Angle : 1pcs
- Pin Header Female 1x8 Straight : 2pcs
- Pin Header Male 1x8 Straight : 2pcs
- Diode 1n4001 : 1pcs
- Tactile Button 6x6x5 Right Angle : 2pcs
- Mini Slide Switch : 1pcs
- Socket DC PCB Mount : 1pcs
- M3x6 Black Pan Padded Screw : 4pcs
- M3x5 Male-Female Nylon Spacer : 4pcs
- M3x10 Female-Female Nylon Spacer : 4pcs
- M3x7x1 Nylon Flat Washer : 4pcs
- RGB444 Base Board : 1pcs
- RGB444 MinSys Board : 1pcs
- Kabel DC Adaptor Charger USB Male to DC 5.5mm : 1pcs
Code
Source code for this LED Cube RGB 4x4x4 also based on Asher Glick's and modified to work with the schematic used here. Source code are available at : https://github.com/paulustanuri/PT018_RGB_LED_Cube_V3.1
Tersedia di
The circuit boards with all the components needed are available in a form of a Kit, complete with the jigs needed.
Available at marketplaces below :
- https://bit.ly/TP-PALTA (Tokopedia)
- https://bit.ly/SP-PALTA (Shopee)
- https://bit.ly/Tindie-PALTA (Tindie)
Cara Membuat
The tutorial to assemble and make this LED Cube can be watch at the video below :